Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision		 Previous revision
Last revisionBoth sides next revision
ldgraphy [2020/11/07 21:01] – yairldgraphy [2020/11/09 14:09] – yair
Line 6: Line 6:
 first go\\ first go\\
 {{ldr-003.mp4}} {{ldr-003.mp4}}
 +
 +===TODO===
 +find out what's up with the Y axis galvo. it gets very hot when on and doesnt move. 
  
 ===hardware=== ===hardware===
 Shih [[http://tribe-against-machine.org/wiki/tiki-index.php?page=Maskless_Photolithography_with_Conductive_Fabric_and_DIY_Laser_Galvanometers|notes]], similar to [[https://github.com/hzeller/ldgraphy/blob/master/design.md|ldgraphy]] Shih [[http://tribe-against-machine.org/wiki/tiki-index.php?page=Maskless_Photolithography_with_Conductive_Fabric_and_DIY_Laser_Galvanometers|notes]], similar to [[https://github.com/hzeller/ldgraphy/blob/master/design.md|ldgraphy]]
  
-the scanner set if PT-A40+the scanner is PT-A40
  
 {{:pasted:20201107-143303.png?400}} {{:pasted:20201107-143303.png?400}}
  
 {{:pt-a40.pdf|manual for PT-A40}} {{:pt-a40.pdf|manual for PT-A40}}
 +
 +
 +
 +what's inside?
 +
 +{{youtube>HIBH55cbfLM?medium}}
 +
 +AlliExp stroe (not he one sent)- https://gzsevenstarlight.aliexpress.com/store/3904033\\
 +pro ThorLAB - https://www.thorlabs.com/newgrouppage9.cfm?objectgroup_id=3770 \\
  
 **Basic Tuning**\\ **Basic Tuning**\\
Line 27: Line 39:
   * Connect computer with ILDA test pattern, run it at approx. 20kpps.   * Connect computer with ILDA test pattern, run it at approx. 20kpps.
   * Power on the amplifiers.   * Power on the amplifiers.
-  * Slowly open the servo gain (clockwise). The mirror of the galvo should move now to its middle position. If yes, turn two rounds clockwise. +  * Slowly open the **servo gain** (clockwise). The mirror of the galvo should move now to its middle position. If yes, turn two rounds clockwise. 
-  *  Slowly open the size until you see the galvo moving. +  *  Slowly open the **size** until you see the galvo moving. 
-  *  Increase servo gain until you see overshoots. Correct it with LFD. +  *  Increase **servo gain** until you see overshoots. Correct it with **LFD**. 
-  *  Decrease undershoots by opening the HFD pot slightliy clockwise. Remove gain/LFD procedure and correct with HFD, until you the picture looks satisfying. Carefully fine tune the driver. The better your fine tuning is, the faster is the scanspeed.+  *  Decrease undershoots by opening the **HFD** pot slightly clockwise. Remove **gain/LFD** procedure and correct with **HFD**, until you the picture looks satisfying. Carefully fine tune the driver. The better your fine tuning is, the faster is the scanspeed.
   * Increase speed of test patterns and readjust for optimized picture   * Increase speed of test patterns and readjust for optimized picture
  
 +{{:pasted:20201107-194611.png?500}}
  
 ===software=== ===software===